JETI Motor Controllers Speed Controls from Hobby Lobby!

Jeti controllers for brush motors -- for flyers who hate reading operating manuals
Jeti brings you more control options but with fewer directions to follow. You can program each of these controllers to follow one of 4 operating conditions by simply changing the location of the little jumper pin on the controller. The 4 operating conditions are: 1. Propeller Brake ON, Battery type NiCd or NiMh, Motor cut-off at 4 Volts (or 0.7V per cell) 2. Prop Brake OFF, Battery type NiCd or NiMh, gradual Motor cut-off at 4 Volts (or 0.7V per cell) 3. Prop Brake ON, Battery type Li-poly, gradual Motor cut-off at minimum voltage 5.2V with 2 Li cells, and 8V with 3 Li cells 4. Prop Brake OFF, Battery type Li-polymer, gradual Motor cut-off at minimum voltage 5.2V with 2 Li cells, and 8V with 3 Li-Po cells These controllers all have: high rate variable switching (1000-4000 Hz), with high output BEC (Battery Eliminator Circuit: powers receiver and servos from the big motor battery) that allows a lot of servos to operate, user-programmable settings as listed above, automatic adjustment of the throttle range, safe "power on" arming (keeps motor from starting when not expected), "soft start up" to prevent propeller or gearbox damage, automatic shut down when signal is lost, and limited maximum braking action to prevent prop or gear damage. They also have automatic current limiting that will allow the current to your motor to exceed the normal level by about 5 Amps before cutting off. JES006 through JES045 are Lithium Polymer friendly!

For 4 to 8 Ni, 2 to 3 Li-Po cells, 6 to 8 Amps
.7 x .6 x .2", .2 oz.	JES006 Jeti 6 Amp Microprocessor Motor Controller ..... $ 23.90 AVAILABLE NOW PCJES006 Jeti 6 Amp Microprocessor Speed Control with Deans Connectors ..... $ 26.90 AVAILABLE NOW

For 4 to 8 Ni, 2 to 3 Li-Po cells, 12 to 15 Amps
1 x .75 x .3", .53 oz.	JES012 Jeti 12 Amp Microprocessor Motor Controller ..... $ 33.80 AVAILABLE NOW PCJES012 Jeti 12 Amp Microprocessor Speed Control with SPEED 400 Connectors ..... $ 39.90 AVAILABLE NOW

For 4 to 8 Ni, 2 to 3 Li-Po cells, 20 to 22 Amps
	JES020 Jeti 20 Amp Microprocessor Motor Controller ..... $ 37.90 ESTIMATED ARRIVAL 09/12/08 - Please Preorder Now 1 x .75 x .3", .53 oz. PCJES020 Jeti 20 Amp Microprocessor Speed Control with Deans Ultra Connectors ..... $ 44.90 AVAILABLE NOW

For 6 to 12 Ni, 2 to 4 Li-Po cells, 30 to 35 Amps
	JES030 Jeti 30 Amp Microprocessor Motor Controller ..... $ 43.50 AVAILABLE NOW 1.3 x 1 x .3", 1 oz. PCJES030 Jeti 30 Amp Microprocessor Speed Control with Deans Ultra Connectors ..... $ 49.90 AVAILABLE NOW

For 6 to 12 Ni, 2 to 4 Li-Po cells, 45 to 50 Amps
	JES045 Jeti 45 Amp Microprocessor Motor Controller ..... $ 61.90 AVAILABLE NOW 1.3 x 1 x .3", 1 oz.


Jeti controllers for brush motors -- for use with NiCad and Nickel Metal Hydride Batteries

For electric heli's, 6-12 cells, no motor cutoff
	For 6-12 cells, 30 Amps continuous current, BEC for receiver and up to 3 servos, no motor cutoff in BEC to avoid sudden landings when battery goes down, has current limiter protection that stops motor if it is blocked, no prop brake, 1000 Hz. switching frequency, adjustable pot for motor start point, 1 oz., 43x22x10mm. Self adjusts to transmitter motor start point, gives more linear throttle response. JE300HE Jeti 300 Heli Microprocessor Motor Control ..... $ 42.90 AVAILABLE NOW

For 8-30 cells and 45 amps continuous current
	For 8-30 cells, 45 Amps continuous current and 60 Amps for up to 30 seconds. No BEC. JE450 Jeti 450 Microprocessor Motor Controller ..... $ 52.90 AVAILABLE NOW

8 to 30 cell controller for up to 60 amps
	For 8-30 cells, 60 Amps continuous current, no BEC, has current limiter protection that stops motor if it is blocked, on/off brake, adjustable pot for motor start point, LED for brake set, off, and max power, 2400 Hz. switching frequency, 1-3/8 oz., 51x30x10mm. JE60 Jeti 60 Amp Speed Controller ..... $ 77.30 AVAILABLE NOW

Jeti Motor Controllers