LiPo Chargers
for Lithium Polymer
Cells and Battery Packs
Cells and Battery Packs
|
LiPo Chargers
for Lithium Polymer
Cells and Battery Packs |
|
Easy to use automatic Lithium Polymer charger for 1-4 cell packs --
charges at up to 3 amps |
|
 |
 3-1/2" x 2" x 7/8". Fully automatic charger for Lithium Polymer battery packs with 1 to 4 cells. Connect to your auto battery or a 12V power supply. Automatically detects the number of cells with 1 to 3 cell packs, 4 cell packs must be manually set by push button. Charger auto detects the cell capacity and sets the charge current; the charge is monitored continuously through the charging process and the optimum charge rate maintained. LED's indicate charge status, blinking LED and audible beep indicates completion of charge. Maximum charge rate is 3 amps. Charger has safety protection for reversed polarity (input or output), low input voltage, incorrect cell count and incorrect cell type (eg. NiCad/NiMH). |
LiPoly Charger for 1-3 cells |
|
 |
3-3/4" x 1-7/8" x 1/2". Charges 1-3 Lithium cells at a charge rate from 110 mA to 1200 mA. Use jumper connections to select the number of cells to be charged and the charge rate. If you select the wrong number of cells or hook the battery up backwards, the charger’s red LED will blink repeatedly and it will not start the charge. Charging process is automatic and a green LED indicates completion. A JST Female connector for connecting the battery to be charged is included. |
Charges 1-3 LiPoly Cells and 1-8 NiCad/NiMH cells |
|
 |
3-3/4" x 1-7/8" x 1/2". Charges 1-3 Lithium cells or 1-8 NiCad/NiMH cells at a charge rate from 110 mA to 1200 mA. Use jumper connections to select the number of cells to be charged and the charge rate. If you select the wrong number of cells or hook the battery up backwards, the charger’s red LED will blink repeatedly and it will not start the charge. Charging process is automatic and a green LED indicates completion. A JST Female connector for connecting the battery to be charged is included. |
Able
to charge 1-4 Li-Poly cells at up to 2-1/2 amps |
|
 |
4-1/8" x 2-1/8" x 1/2". Charges 1 to 4 cell lithium cells at a charge rate from 250 mA to 2500 mA. Make jumper connections to select the number of cells to be charged and the charge rate. If you select the wrong number of cells or hook the battery up backwards, the charger's red LED will blink repeatedly and it will not start the charge. This makes it impossible to inadvertently charge a 2 cell pack on the 3 cell setting, or charge at too high a rate which would destroy the battery. Charging process is automatic and a green LED indicates completion. Connects to any 12 volt battery or power supply. A JST female connector for connection to the battery being charged is included. |
Charge 1-5 LiPoly cells at up to 3-1/2 amps |
|
 |
4" x 1-3/4" x 3/4". Charges 1-5 lithium cells at rates up to 3.5 amps. Push button operation allows you to easily set the cell count and charge rate. LED's indicate cell count, charge rate, and charging status. Audible beeps and solid LED light indicate that charging is complete. Reverse polarity protection (input and output). Connects to a 12-volt battery or power supply with the included alligator clips. Banana plugs with a JST charge connector are included. Rugged aluminum case with good cooling for trouble free operation. |
NEW! Balance and charge your 1-5 cell Lithium battery packs - also charges NiMH, NiCd, and Lead Acid batteries |
|
|
|
5-1/4" x 3-1/4" x 1-1/8". Intelligent multi-function microprocessor controlled charger. Charge your 1 to 5 cell LiPo packs from a 12-volt battery or 12-volt DC power supply. Lithium packs with compatible balance plugs can be balance charged. Each individual cell in the pack is monitored and charged independently; when finished each cell is charged and voltage matched to the other cells in the pack. Greatly extends the life of your batteries and improves their performance. Unit also charges NiMH or NiCad packs (1-14 cells) and Lead Acid batteries of 6 or 12 volts. Input voltage range 10-18 volts, charge rates from 0.1 to 5.0 amps. Comes with clear English instructions and is easy and intuitive to program. Includes an assortment of output connectors, one each for JST, Glow driver, Receiver battery, and Alligator clips. A partial list of the Lipo batteries with compatible balance connectors is: Art-Tech, ESky, E Max, Riccs, and Shida.
Check out the RCGroups.com Review of SKM601B! |
Charges Lithium, Nicad or NiMH cells at up to 7 amps |
|
 |
4-1/2" x 3-1/2" x 1-1/4". Charges 1-5 Lithium cells, 1 to 14 NiCad or NiMH cells. Versatile and powerful charger with a charge rate of up to 7 amps. Micro-processor controlled fast charger, discharger and battery conditioner for Nicad, NiMH, Lithium Polymer, Lithium Ion and Lead Acid batteries. Connects to any 12-volt battery or power supply. Easy to navigate menu structure quickly and clearly gets you ready to charge. Illuminated digital LCD screen displays battery type, charge/discharge, mAh, voltage and charging time. Warnings for incorrect polarity, low input voltage, incorrect cell count and over time limit are shown on the LCD screen. Connect to battery pack with banana plugs like HLFK156 (not included). |
Charge 1 to 4 LiPoly cells at up to 2-1/2 amps |
|
 |
4 x 1-3/4 x 5/8". Charges 1-4 lithium cells at rates up to 2.5 Amps. Push button operation allows you to easily set the cell count and charge rate. LED’s indicate cell count, charge rate and charging status. Audible beeps and a solid LED light indicate that charging is complete. Reverse polarity protection (input and output). Connects to a 12 volt battery or power supply. Banana plugs with JST charge connector included. |
Charges 1 to 5 Lithium cells or 1 to 12 NiCad/NiMH cells at up to 5 amps |
|
 |
5-1/8" x 4-1/2" x 1-1/2". Micro-processor controlled fast charger, discharger and battery conditioner for NiCad, NiMH, Lithium Polymer, Lithium Ion, and Lead Acid batteries. Connects to any 12-volt power supply. Clear instructions explain the specific programs for charging each type of battery. Cut-off for NiCad and NiMH cells is by "Delta Peak" method. Lithium Polymer and Lithium Ion charging program uses the constant current/constant voltage method. Warnings for incorrect polarity, low input voltage, incorrect cell count and over time limit are shown on the display screen. Battery conditioning of NiCad and NiMH cells through repeated charge/discharge cycles is programmable for up to 5 cycles. Charges at up to 5 amps and discharges at up to 1 amp. |
Charges 1 to 5 Lithium cells or 1 to 14 Nicad or NiMH cells at up to 5 amps |
|
 |
4-5/8" x 3-5/16" x 1-1/8". Rugged aluminum case, will safely charge and discharge Lithium, NiCad, NiMH and Lead-Acid battery packs and cells. Easy to read. Illuminated digital LCD screen displays battery type, charge/discharge, mAh, voltage and charging time. Charges at up to 5 amps and discharges at up to 1 amp. Battery conditioning of Nicad and NiMh cells thru repeated charge/discharge cycles, is programmable for up to 5 cycles. To insure proper use, the LCD screen will also display error messages for out-of-range input voltage, incorrect connection or reversed polarity, poor battery condition and internal errors. Easy to use 4 button control panel and logical menus. |
NEW! Safely charge 1-10 Li-Poly, Li-Ion, or the new A123 cells |
|
 |
6-1/4" x 3-1/4" x 2-1/4", weighs 22 oz. Charge rates from 50mA up to 8 amps (4 amp maximum when charging 10 cells). Charges Lithium Polymer cells, Lithium Ion cells, and A123 Lithium Manganese cells. Easy to use menus with large, four line LCD display. Enter the cell count and milliamp settings. Has multiple memories for your favorite packs. Includes cell count verification and joystick navigation. Also includes a temperature probe, which if it detects a rise in temperature, will shut down the charging process. Charger connects to a 12-volt battery source. User can set maximum voltage, from 4.2 volts (maximum power) down to 3.7 volts (storage charge). Built-in wattmeter handles up to 100 amp peaks, displays Volts, Amps, Watts and Horsepower. Expansion data port for future add-ons like cell balancer, PC interface, tachometer, etc. Free lifetime updates online. Housing is made of aluminum. |
NEW! Update your TME Xtrema charger to the latest software |
|
 |
6' cable connects Xtrema charger to your computer with a RS-232 female connector, includes the USB to RS-232 adapter cable. Using the cable you can download the powerful XtremaLog program for FREE. The Xtrema's usefulness expands to include charge and power analyzer features via an optional data cable and your computer. With the XtremaLog program used as a power analyzer, you can let your computer log the numbers and analyze your results. Compatible with Windows 98SE, ME, 2000, XP and Vista via standard USB and/or RS-232 ports. Comes with written instructions. |
 |
This cable is for those who have the Xtrema RS-232 cable but do not have the USB adapter cable. Allows you to connect your Xtrema charger with any USB open port on your computer. |
Charges up to 30 Nicads (at rates up to 7 Ah), up to 30 NiMH batteries, up to 10 Lithium Cells, up to 24V Lead Acid |
|
 |
The ultimate field charger. 6" x 5-3/8" x 1-5/8", 26 oz. Recharges, conditions, balances, measures capacity of Nicads. Recharges, discharges to measure capacity of NiMH batteries. Charges, discharges to determine capacity of Lithium cells and Lead Acid batteries. Clear instructions, relatively easy to set. Can be adjusted to accept low car (input) battery voltage. For knowledgeable users this charger allows changing of Delta V for automatic cutoff, trickle current. Has adjustable safety timer, click sound when buttons are successfully pressed, buzzer sound for errors and completions. Allows separate charging of receiver or transmitter batteries. |
Charging Lithium Polymer batteries just got safer |
|
 |
LipoSack - 9" wide and 12" long, weighs 4 oz. LipoSack will allow you to charge most Lithium Polymer packs and reduce the effects of a Lithium Polymer battery charging mishap. Place LipoSack on a non-flammable surface during charging process. Route charging leads through vent at the top seam of the LipoSack. Close top flap of LipoSack and press hook and loop closure. Charge your battery using proper charging practices. Always monitor your charging batteries and never leave them unattended. |
Banana plugs for charger connections |
|
 |
Banana plugs for electrical connections to most chargers and field box power panels, 1 red, 1 black. |
Phone: 1-866-WE-FLY-RC (1-866-933-5972)
Fax: 615-377-6948
Copyright © 1996-2008 Hobby Lobby International, Inc. All Rights Reserved.
