"Atlas Black" Brushless Controllers

Fully programmable brushless motor controllers

Atlas Black programmable Brushless motor controls

Atlas motor controllers will work with all types of brushless motors. Atlas controllers come pre-programmed and are ready to use when you receive them. Additional controller adjustments are available; most can be accessed and adjusted with your transmitter, but for easier programming, use the included program card to set all your options. This only takes a few seconds. Settings can easily be changed at the flying field without the need for additional instructions or a computer.

Atlas Black Opto Controllers
When you need more than 3 Lithium cells in your flight pack it is necessary to use an "Opto" controller. Opto controllers do not have a BEC (battery eliminator circuit) to power your radio receiver and servos. An alternate power supply is necessary. Use either a standard 4.8V receiver battery pack or a UBEC (KFS001 - KFS003). A UBEC is a device that reduces the high voltage of your flight batteries and supplies regulated power suitable to run your receiver and servos.

Every Atlas programmable brushless motor controller has:

A 3-Year Warranty
A FREE Programming Card
Over-temperature protection
Works with any brushless motor
Can be used in airplanes or helicopters (has governor mode)
An easy to use programming guide

Every Atlas controller can be programmed for:

NiMH or Lithium Batteries (Type and number of cells)
Hard or Soft Start
Motor Timing:
Auto Detect
Soft "Inrunners" (0 to 7 degrees)
Hard "Outrunners" (22 to 30 degrees)
Brake: On/Off
Motor Rotation:
Normal
Reverse
Low Voltage Cut Off:
Ignore
Reduce Power
Hard Cut Off
Governor Mode (Helicopter use)

Atlas Black Controllers PDF Instruction Manual

Atlas Black 8 Amp

1-3/8" x 7/8" x 3/8", 11 grams (1/3 oz.). 8 Amps continuous, for 5 to 10 NiCd or NiMH, 2 to 3 Lithium cells. BEC can run 4 servos on 6 cell battery, 2 servos on 10 cells. Order connector set MJ21011.

Atlas Black 12 Amp

1-3/8" x 7/8" x 3/8", 11 grams (1/3 oz.). 12 Amps continuous, for 5 to 10 NiCd or NiMH, 2 to 3 Lithium cells. BEC can run 4 servos on 6 cell battery, 2 servos on 10 cells. Order connector set MJ21011.

Atlas Black 20 Amp

1-7/8" x 7/8" x 3/8", 19 grams (5/8 oz.). 20 Amps continuous, for 5 to 10 NiCd or NiMH, 2 to 3 Lithium cells. BEC can run 4 servos on 6 cell battery, 2 servos on 10 cells. Order connector set MJ21011.

Atlas Black 35 Amp

1-7/8" x 15/16" x 1/2", 31 grams (1-1/8 oz.). 30 Amps continuous, for 5 to 10 NiCd or NiMH, 2 to 3 Lithium cells. BEC can run 4 servos on 6 cell battery, 3 servos on 10 cells. Connectors included.

Atlas Black 45 Amp

3-1/8" x 1-1/16" x 3/8", 39 grams (1-1/3 oz.). 45 Amps continuous, for 5 to 10 NiCd or NiMH, 2 to 3 Lithium cells. BEC can run 5 servos on 6 cell battery, 3 servos on 10 cells. Connectors included.

Atlas Black 45 Amp Opto

3-1/8" x 1-1/16" x 3/8", 34 grams (1-1/5 oz.). 45 Amps continuous, for 6 to 16 NiCd or NiMH, 2 to 5 Lithium cells, Connectors included. No BEC.

Atlas Black 75 Amp

3-1/8" x 1-1/16" x 3/8", 50 grams (1-3/4 oz.). 75 Amps continuous, for 5 to 10 NiCd or NiMH, 2 to 3 Lithium cells. BEC can run 5 servos on 6 cell battery, 3 servos on 10 cells. Connectors included.

Atlas Black 75 Amp Opto

3-1/8" x 1-1/16" x 3/8", 46 grams (1-5/8 oz.). 75 Amps continuous, for 6 to 16 NiCd or NiMH, 2 to 5 Lithium cells, Connectors included. No BEC.

Atlas Black 90 Amp Opto

2-5/8" x 2-1/16" x 11/16", 115 grams (4 oz.). 90 Amps continuous, for 16-30 NiCd or NiMH, 5-10 Lithium cells. Use with large OUTRUNNER motors in demanding applications. Solid screw-in-place installation, 3 rubber grommet shock mounts. 2.5mm silicone insulated wire on motor leads, 3mm silicone insulated wire on battery leads. 13" long wire to receiver. Connectors included. No BEC.

Large 2" x 2" x 5/16" aluminum heat sink dissipates excess heat to keep the controller in a safe operating temperature range.

Spare Programming Card, 8 - 75 Amp

1-1/4" x 1-7/8" x 1/16" card with jumper connectors programs the 8A to 75A Atlas controllers. Pick the program options that you want by moving the jumpers to the appropriate pins on the card, plug your Atlas controller into the Program Card, switch on the controller for a few seconds and your settings have been programmed; a "Beep" tone verifies the process. A 4.8V receiver battery is required to program the Opto controllers. Changes take only seconds to perform; no other support equipment or computer is required.

With the Programming card you can select:

NiCd and NiMH or Lithium battery (Type and cell count)
Hard or Soft Start
Hard or Soft Cutoff
Timing:
Low for Inrunners
High for OUTRUNNERS
Auto Detect
Brake On or Off
Direction of Rotation of Motor
Governor Mode for Helicopters

Spare Programming Card, 90 Amp

Phone: 1-866-WE-FLY-RC (1-866-933-5972)
Fax: 615-377-6948